MARPOL Seminar 23 mei 2013
Programma • • • • • • • • • •
13.30 – 13.40 13.40 – 14.05 14.05 – 14.30 14.30 – 14.55 14.55 – 15.15 15.15 – 15.40 15.40 – 16.05 16.05 – 16.30 16.30 – 17.00 17.00
Opening MARPOL Annex IV en V MARPOL Annex VI, SOx en Nox EEDI, SEEMP, EEOI Pauze Handhaving Inspecties door havens EEDI verificatie Forumdiscussie Netwerkgelegenheid
Chris Dijkmans Marja Tiemens Jaap Kolpa Sibrand Hassing Inspectie IL&T Cees-Willem Koorneef Michiel Verhulst Dagvoorzitter
MARPOL ANNEX IV & V 23 – 05 - 2013
Marja C. Tiemens-Idzinga Ministerie van Infrastructuur en Milieu Directoraat - Generaal Bereikbaarheid (DGB) Maritieme Zaken – afdeling Zeevaart en Security
MCTI
MARPOL ANNEX IV
CHAPTER 1 – GENERAL CHAPTER 2 – SURVEY & CERTIFICATION CHAPTER 3 – EQUIPMENT AND CONTROL OF DISCHARGE CHAPTER 4 – RECEPTION FACILITIES CHAPTER 5 – PORT STATE CONTROL MCTI
Regulation 1 - Definitions Sewage means drainage from: Toilets Medical units
Live animal spaces Mixed waste waters (if involving the above) MCTI
Regulation 9 - Sewage Systems Every ship to which this Annex applies shall be equipped with one of the following: • Sewage treatment plant type approved by the Administration, see MEPC.159(55) more to come • Sewage comminuting and disinfecting system approved by the Administration plus temporary storage when the ship is less than 3 nautical miles from nearest land • A holding tank with capacity for retention of all sewage to the satisfaction of the Administration MCTI
Sea Area
Discharge criteria – Regulation 11
Within 3 nm from land
No discharge except from an approved/certified sewage treatment plant
Between 3 and 12 nm from land
No discharge except (1) from approved/certified sewage treatment plant or (2) approved comminuting and disinfecting system
More than 12 nm
Discharge from either (1) or (2) Or sewage from a holding tank when proceeding at not less than 4 knots at a rate approved by the Administration.
MCTI
MARPOL – ANNEX IV amendments per 01-01-2013
MCTI
RESOLUTION MEPC.200(62) Adopted on 15 July 2011
Special Area provisions and the designation of the Baltic Sea as a Special Area under MARPOL Annex IV the said amendments entered into force on 1 January 2013
12bis
Reception facilities for passenger ships in Special Areas MCTI
Discharge of sewage from passenger ships within a special area The discharge of sewage from a passenger ship within a special area
shall be prohibited:
a) for new passenger ships on and
or after 1 January 2016
b) for existing passenger ships on or after 1 January 2018 both subject to regulation 12bis, subparagraph 2 (notification to IMO)
except when the following conditions are satisfied: the ship has in operation an approved sewage treatment plant which has been certified by the Administration to meet the operational requirements referred to in regulation 9.2.1 of this Annex, and the effluent shall not produce visible floating solids nor cause discoloration of the surrounding water. 9.2.1 refers to a sewage treatment plant taking into account 227(64) MCTI
Sewage treatment plant type approved by the Administration, see MEPC.159(55)
RESOLUTION MEPC.227(64) Adopted on 5 October 2012 2012 GUIDELINES ON IMPLEMENTATION OF EFFLUENT STANDARDS AND PERFORMANCE TESTS FOR SEWAGE TREATMENT PLANTS
SUPERSEDES MEPC.159(55)
MCTI
Sewage treatment plants installed prior to 1 January 2016 and on or after 1 January 2010, on ships other than passenger ships operating in MARPOL Annex IV special areas and intending to discharge treated sewage effluent into the sea, should comply with resolution MEPC.159(55). Sewage treatment plants installed prior to 1 January 2010 on ships other than passenger ships operating in MARPOL Annex IV special areas and intending to discharge treated sewage effluent into the sea, should comply with resolution MEPC.2(VI).
INVITES Governments to: implement the 2012 Guidelines and apply them on or after 1 January 2016; and provide the Organization with information on experience gained with the application of the 2012 Guidelines MCTI
MARPOL ANNEX V 31 December 1988
MCTI
MEPC 61 – September 2010 *Approval of the revised MARPOL Annex V General prohibition Adjusted definitions Discharge en route Discharge requirements inside & outside SA Criteria for harmful solid bulks to be developed
* Continuation of the CG to develop guidelines MCTI
MEPC 62 – July 2011 revised Annex V adopted
MEPC.201(62) entry into force on 1 January 2013 • Continuation of the CG to develop guidelines • Development of criteria for solid bulk cargoes MCTI
MEPC 63 – March 2012 2012 guidelines for the implementation of MARPOL Annex V MEPC.219(63)
2012 guidelines for the development of garbage management plans MEPC.220(63)
MCTI
MCTI
Type of garbage
Ships outside SA’s
Ships within SA’s
Food waste comminuted or ground
Discharge permitted
Discharge permitted
≥ 3 nm from the nearest land, en route
≥ 12 nm from the nearest land, en route
Discharge permitted
Discharge prohibited
Food waste not comminuted or ground
Cargo residues1 not contained in wash water Cargo residues1 contained in wash water Cleaning agents and additives1 contained in cargo hold wash water
≥12 nm from the nearest land, en route
Discharge prohibited Discharge permitted ≥12 nm from the nearest land, en route
Discharge not permitted2 ≥12 nm from the nearest land, en route
Discharge not permitted2 ≥12 nm from the nearest land, en route
Discharge permitted Cleaning agents and additives1 in deck and external surfaces wash water Animal carcasses carried on board as cargo and which died during the voyage All other garbage - plastics, domestic
Discharge permitted
Discharge permitted Discharge prohibited as far as possible from nearest land, en route Discharge prohibited Discharge prohibited
wastes, cooking oil, incinerator ashes, operational wastes,fishing gear
Mixed garbage
When garbage is mixed with or contaminated by other substances prohibited from discharge or having different discharge requirements - the more stringent requirements shall apply
1 These substances must not be harmful to the marine environment; 2 According to regulation 6.1.2 of MARPOL Annex V the discharge shall only be allowed if: (a) both the port of departure and the next port of destination are within the special area and the ship will not transit outside the special area between these ports; and (b) if no adequate reception facilities are available at those ports
The revised ANNEX V
mandatory documents on board * Placards (every ship ≥12 metres) * Garbage management plan (every ship ≥100GT and every ship certified to carry ≥15 persons) * GRB (every ship ≥400GT and every ship certified to carry ≥15 persons)
MCTI
discussion
SOLID BULK CARGOES
MCTI
MEPC 59 – JULY 2009 Submission by BIMCO and Intercargo Problem with SRF for solid dry bulk in Mediterranean Sea and Gulfs area
1 May 2009 1 Aug 2008 Effective SA MCTI
Short term
MCTI
MEPC 60 – March 2010 * Resolution MEPC.191(60) – 1 May 2011
* MEPC.1/Circ.675/Rev.1
Dry bulk in the MED & GULF & WCR SHORT TERM SOLUTION MCTI
MCTI
Type of garbage
Ships outside SA’s
Ships within SA’s
Food waste comminuted or ground
Discharge permitted
Discharge permitted
≥ 3 nm from the nearest land, en route
≥ 12 nm from the nearest land, en route
Discharge permitted
Discharge prohibited
Food waste not comminuted or ground
Cargo residues1 not contained in wash water Cargo residues1 contained in wash water Cleaning agents and additives1 contained in cargo hold wash water
≥12 nm from the nearest land, en route
Discharge prohibited Discharge permitted ≥12 nm from the nearest land, en route
Discharge not permitted2 ≥12 nm from the nearest land, en route
Discharge not permitted2 ≥12 nm from the nearest land, en route
Discharge permitted Cleaning agents and additives1 in deck and external surfaces wash water Animal carcasses carried on board as cargo and which died during the voyage All other garbage - plastics, domestic
Discharge permitted
Discharge permitted Discharge prohibited as far as possible from nearest land, en route Discharge prohibited Discharge prohibited
wastes, cooking oil, incinerator ashes, operational wastes,fishing gear
Mixed garbage
When garbage is mixed with or contaminated by other substances prohibited from discharge or having different discharge requirements - the more stringent requirements shall apply
1 These substances must not be harmful to the marine environment; 2 According to regulation 6.1.2 of MARPOL Annex V the discharge shall only be allowed if: (a) both the port of departure and the next port of destination are within the special area and the ship will not transit outside the special area between these ports; and (b) if no adequate reception facilities are available at those ports
2012 guidelines for the implementation of MARPOL Annex V MEPC.219(63)
chapter 3 - criteria for solid bulk cargoes
MCTI
HME CRITERIA Cargo residues are considered harmful to the marine environment if they are residues of solid bulk substances which are classified according to the criteria of the UN GHS system, meeting one of the seven parameters in paragraph 3.2 in the 2012 Guidelines for implementation of Annex V Acute Aquatic Toxicity Chronic Aquatic Toxicity Carcinogenicity combined with degradable and having high bioaccumulation Mutagenicity combined with not being rapidly degradable and having high bioaccumulation Reproductive Toxicity combined with not being rapidly degradable and having high bioaccumulation Specific Target Organ Toxicity Repeated Exposure combined with not being rapidly degradable and having high bioaccumulation Solid bulk cargoes containing or consisting of synthetic polymers, rubber, plastics, or plastic feedstock pellets (this includes materials that are shredded, milled, chopped or macerated or similar materials) MCTI
HME
OR NOT HME
MCTI
INTERIM MEASURES
MEPC.1/Circ.791 18 October 2012 Provisional classification of solid bulk cargoes under the revised MARPOL Annex V between 1 January 2013 and 31 December 2014
shippers of solid bulk cargoes should classify those cargoes using the seven criteria
to be continued MCTI
MCTI
Laatste ontwikkelingen MARPOL Annex VI en Europese regelgeving Jaap Kolpa, Ministerie van IenM Harderwijk, 23 mei 2013
1. Regelgeving op gebied van zwavelemissies
30
Ministerie van Infrastructuur en Milieu
23 mei 2013
Aanscherping Marpol Annex VI: Maximale zwavelgehalte in scheepsbrandstof: Tot 30 juni 2010
Mondiale zwavel limiet
SECA zwavel limiet
4,50 %
1,50 % 1,00 %
1 juli 2010 januari 2012
3,50 % 0,10 %
1 januari 2015 1 januari 2020 *)
0,50 %
*) Evaluation in 2018; in case of negative results, the introduction date will shift from 2020 to 2025
31
Ministerie van Infrastructuur en Milieu
23 mei 2013
Europese ‘kop’ op mondiale IMO-regelgeving: Mondiale zwavelnorm in 2020 omlaag van 3,5 % naar 0,5 %. Mocht uit de IMO evaluatie in 2018 blijken dat in 2020 onvoldoende laagzwavelige brandstof beschikbaar is, dan verschuift de ingangsdatum naar 2025. De EU houdt, voor EU-wateren, vast aan 2020 als ingangsdatum voor die 0,5 % norm, ongeacht wat IMO besluit (EU-Zwavelrichtlijn 1999/32/EC) 32
Ministerie van Infrastructuur en Milieu
23 mei 2013
MARPOL limits on sulphur content in marine fuels
Ministerie van Infrastructuur en Milieu
23 mei 2013
SECA = SOx Emission Control Area
34
Ministerie van Infrastructuur en Milieu
23 mei 2013
SECA Noord-Amerika vanaf 1 augustus 2011
200 mijlen vanuit de Noordamerikaanse kust 35
Ministerie van Infrastructuur en Milieu
23 mei 2013
Zwavelnormen zeevaart vergeleken met normen voor wegvervoer en binnenvaart:
36
Ministerie van Infrastructuur en Milieu
23 mei 2013
Zwavelnormen zeevaart vergeleken met normen voor wegvervoer en binnenvaart: Zeevaart norm voor SECA’s (2015): 0,1 % (1000 ppm)
37
Ministerie van Infrastructuur en Milieu
23 mei 2013
Zwavelnormen zeevaart vergeleken met normen voor wegvervoer en binnenvaart: Zeevaart norm voor SECA’s (2015): 0,1 % (1000 ppm) Binnenvaart (ingegaan 2011): 0,001% (10 ppm)
38
Ministerie van Infrastructuur en Milieu
23 mei 2013
Zwavelnormen zeevaart vergeleken met normen voor wegvervoer en binnenvaart: Zeevaart norm voor SECA’s (2015): 0,1 % (1000 ppm) Binnenvaart (ingegaan 2011): 0,001% (10 ppm)
Wegvervoer (ingegaan 2009): 0,001% (10 ppm) 39
Ministerie van Infrastructuur en Milieu
23 mei 2013
2. Regelgeving op gebied van stikstofoxide-emissies
40
Ministerie van Infrastructuur en Milieu
23 mei 2013
41
Ministerie van Infrastructuur en Milieu
23 mei 2013
Voor schepen gebouwd tussen 1990 en 2000 met grote motoren geldt ook Tier I, wanneer: • vermogen > 5000 kW • cilinderinhoud > 90 liter (Tier I: 17.0 g/kWh bij 130 omwentelingen
per minuut)
42
Ministerie van Infrastructuur en Milieu
23 mei 2013
g/kWh 18
NOx-normen Marpol Annex VI vergeleken met EUnormen wegtransport Tier I
16
Tier II
14 12 10 8 6 4 2
Euro I Euro II Euro III
Tier III
Euro IV Euro V Euro VI
0
Ministerie van Infrastructuur en Milieu
23 mei 2013
NECA Noord-Amerika vanaf óf 1 januari 2016 óf 1 januari 2021
200 mijlen vanuit de Noordamerikaanse kust 44
Ministerie van Infrastructuur en Milieu
23 mei 2013
Worden Noordzee, Het Kanaal en de Baltische Zee aangewezen als NECA?
45
Ministerie van Infrastructuur en Milieu
23 mei 2013
Baltische Zee een NECA? Beslissing over aanvraag bij
IMO ligt ter tafel bij de Baltic Marine Environment Protection Commission (ook bekend als de Helsinki Commissie, HELCOM)
46
Ministerie van Infrastructuur en Milieu
23 mei 2013
Noordzee en Het Kanaal een NECA? Dit dossier bevindt zich in de studiefase. Twee rapporten zijn hierover uitgekomen:
47
Ministerie van Infrastructuur en Milieu
23 mei 2013
BEDANKT VOOR UW AANDACHT ! 48
Ministerie van Infrastructuur en Milieu
23 mei 2013
MARPOL ANNEX VI Energy Efficiency Measures EEDI – SEEMP - EEOI
By: Sibrand Hassing Directorate-General for Mobility and Transport – Shipping & Security
23 May 2013
MARPOL ANNEX VI - EE Content
• Introduction • Why an EEDI & SEEMP? • Main components of Ch. 4 MARPOL Annex VI (I) – EEDI (II) - SEEMP • Likely impacts of EEDI & SEEMP • Latest developments
23 May 2013
MARPOL ANNEX VI - EE Introduction (1) • MEPC 62 agreed 15 July 2011 a new Chapter 4 in MARPOL Annex VI on “Regulations on Energy Efficiency of Ships”* - for ships > 400GT; • Makes mandatory the Energy Efficiency Design Index (EEDI), for new ships; • Makes mandatory the Ship Energy Efficiency Managent Plan (SEEMP), for all ships; • Entered into force on 1 January 2013. * Resolution MEPC.203(62) 23 May 2013
MARPOL ANNEX VI - EE Introduction (2) • EEDI & SEEMP are part of IMOs’ package approach; • ‘Package’ = Technical- (EEDI), Operational(SEEMP) and Marketbased measures; • MBMs’ are on agenda IMO/MEPC; • Outcome not predictable – a very political discussion
23 May 2013
MARPOL ANNEX VI - EE Why an EEDI & SEEMP? • CO2 emissions from ships are expected to increase (approx. 3% in 2007 12-18% in 2050*); • Shipping needs also to take its responsibility; • All emission reducing measures, incl. technical & operational measures - such as EEDI & SEEMP, will also decrease shippings’ CO2 footprint; • Technical- and operational EE measures are identified as measures with a significant potential*; • CO2 emissions are proportional to fuel consumption. * Second IMO Greenhouse Gas Study 2009 23 May 2013
MARPOL ANNEX VI - EE Main components of Ch. 4 MARPOL Annex VI (I) EEDI; • An attained EEDI shall be calculated for ships which falls into one of the categories defined in reg. 2.25 to 2.35 – reg. 20; = EEDI value achieved by an individual ship
• Required EEDI for ships which falls into one of the categories defined in reg. 2.25 to 2.31 – reg. 21; = maximum value of attained EEDI allowed by reg. 21 23 May 2013
MARPOL ANNEX VI - EE The EEDI formula:
23 May 2013
MARPOL ANNEX VI - EE Attained EEDI • • • • • • • • •
Bulk carrier Gas carrier Tanker Container ship General cargo ship Reefer Combination carrier Passenger ship Ro-ro cargo ship (vehicle carrier) • Ro-ro cargo ship • Ro-ro passenger
Required EEDI • • • • • • •
Bulk carrier Gas carrier Tanker Container ship General cargo ship Reefer Combination carrier
23 May 2013
MARPOL ANNEX VI - EE Attained EEDI Required EEDI Attained EEDI ≤ Required EEDI = (1 – X*/100) x Reference line value * Where X is the Reduction Factor Reduction Factor implementation phases: 1. Phase 0 01.01.2013 – 31.12.2014 2. Phase 1 01.01.2015 – 31.12.2019 3. Phase 2 01.01.2020 – 31.12.2024 4. Phase 4 01.01.2025 - ………
(0 or n/a**) (10 or 0 – 10**) (20 – or 0 – 20**) (30 or 0 – 30**)
** pending ship size
23 May 2013
MARPOL ANNEX VI - EE • Reference line refer to statistically average EEDI curves; derived from data of existing ships • Reference line value = a x b-c Parameters can be found in Table 2 to regulation 21.3 • If the design of the ship allows to fall into more than one ship type definitions, the required EEDI for the ship shall be the most stringent (the lowest) required EEDI. • Between Phase 1 and midpoint of Phase 2 – review of the status of technological developments if felt necessary time periods and EEDI reference line parametrs can be amended. • In compliance with the EEDI regulations International Energy Efficiency Certificate (EEDI in grams-CO2/tonne-mile)
23 May 2013
MARPOL ANNEX VI - EE (II) SEEMP (1); Regulation 22 – each ship shall keep on board a specific SEEMP • May form part of the ship’s ISM SMS; • In developing take into account guidelines developed by IMO MEPC.1/Circ.683: GUIDANCE FOR THE DEVELOPMENT OF A SHIP ENERGY EFFICIENCY MANAGEMENT PLAN (SEEMP)* Note: does not need a formal approval by flag State and/or RO *
Still under further development 23 May 2013
Amendments to MARPOL ANNEX VI - EE (II) SEEMP (2); • A list of all the possible stakeholders in the efficiency of a single voyage is long; such as charterers, ports and vessel traffic management services, etc., for the specific voyage. All involved parties should consider and coordinate the inclusion of efficiency measures in their operations both individually and collectively. • Fuel efficient operations, e.g. by: improved voyage planning – weather routeing – just in time – speed optimization – optimized shaft power – optimum trim – optimum ballast - optimum propeller and propeller inflow considerations - optimum use of rudder and heading control systems (autopilots) - hull maintenance - propulsion system maintenance - waste heat recovery - improved fleet management – improved cargo handling – energy management 23 May 2013
MARPOL ANNEX VI - EE INTERNATIONAL ENERGY EFFICIENCY CERTIFICATE
IEE Certificate to be on board all ships! • New ships to certify that: 1. Comply with the applicable EEDI requirements; and 2. Comply with the SEEMP requirements • Existing ships to certify that: 1. Comply with the SEEMP requirements Note: For existing ships, the verification of the requirement to have a SEEMP on board according to regulation 22 shall take place at the first intermediate or renewal survey identified in paragraph 1 of this regulation, whichever is the first, on or after 1 January 2013. 23 May 2013
MARPOL ANNEX VI - EE Energy Efficieny Operational Indicator (EEOI) • Compulsary? - a monitoring system should be in place • Resolution MEPC.213(63): The energy efficiency of a ship should be monitored quantitatively. This should be done by an established method, preferably by an international standard. The EEOI developed by the Organization is one of the internationally established tools to obtain a quantitative indicator of energy efficiency of a ship and/or fleet in operation, and can be used for this purpose. Therefore, EEOI could be considered as the primary monitoring tool, although other quantitative measures also may be appropriate. • EEOI see MEPC.1/Circ.684
23 May 2013
MARPOL ANNEX VI - EE Likely impacts of EEDI & SEEMP • • • •
More energy efficient ships; Use of alternative fuels (e.g. LNG); Slower speed ships (= most effective measure); Pressure on sector to improve its CO2 footprint (especially existing ships); • Increase of newbuilding costs; • Risk of modal shift (especially for short sea). 23 May 2013
MARPOL ANNEX VI - EE Latest developments At MEPC 65 (13 – 17 May 2013), the NL proposal for the introduction of 3 correction factors for small general cargo ships (< 20.000 dwt) was adopted.
Why? Large scatter and low correlation
Cause (disproportional effect of): 1. Operational aspects (dimensions/area of operation) 2. Loading gear (cranes, sideloaders, RoRo ramps) 3. Class notations (eg loading/unloading aground) 23 May 2013
MARPOL ANNEX VI - EE Factors are: fj factor for general cargo ships fiVSE factor for small general cargo ships to correct for additional class notations fl factor for ships equipped with cranes and other cargorelated gear Note: already included in formula shown in sheet #7
23 May 2013
MARPOL ANNEX VI - EE Proposal was based upon a study by:
1. CONOSHIP 2. MARIN 3. CMTI Note: The study indicated that the application of these three factors will provide an incentive to reduce CO2 emissions by this segment. 23 May 2013
Thank you for your attention.
Contactdetails: E:
[email protected] 23 May 2013
Handhaving MARPOL Annex IV, V en VI
M.C. Vink
HH via FSC en PSC • MARPOL conventie Artikel 5 – Controle op certificaat en uitgebreid inspectie op basis van “clear grounds”. – Artikel 4 geeft sancties aan zoals b.v. boetes, voldoende om overtredingen te ontmoedigen (PSC meestal aanhouding) • Procedures for PSC Res A.1052(27) • Artikel per Annex – Annex IV art 13 Familiariteit van de bemanning – Annex V art 8 Familiariteit van de bemanning – Annex VI art 10 Controle op het certificaat (i.o.m. Art 5 v/d Conventie)
Inspectie Leefomgeving en Transport
Uitgewerkt per Annex
Inspectie Leefomgeving en Transport
Annex IV gewijzigd vlg Res MEPC.200(62) • Baltic Sea special area • Nieuwe discharge voorschriften voor passagiers schepen • Gevolg is: – Sanitair afval afgeven – Sanitair afval behandelen door Res. MEPC.159(55) goedgekeurde apparatuur • Pass schip is schip > 12 passagiers dus Bruine vloot ook! • Van kracht vanaf : – Nieuwe schepen 1-1-16 – Bestaande schepen 1-1-18 • Afhankelijk van aanwezigheid sanitair afval ontvangst faciliteiten • HH via bewijzen van afgifte of gebruik van goedgekeurde apparatuur Wel een certificaat maar geen logboek voorgeschreven Inspectie Leefomgeving en Transport
Annex V gewijzigd vlg Res MEPC 201(62) • 9 categorieën vuilnis te vermelden in vuilnis boek. • Elk schip >100 GT en elk schip > 15 personen en drijvende en vaste platforms hebben een vuilnis management plan. • Elk schip > 400 GT en elk schip > 15 personen en drijvende en vaste platforms hebben een vuilnis boek. • Elk schip > 12 m over alles en drijvende en vaste platforms hebben posters die de bemanning en passagiers informeren over de vuilnis behandeling volgens Annex V
Inspectie Leefomgeving en Transport
Annex V en droge lading restanten • Ruim bilge water dat ladingdelen bevat mag overboord als het niet schadelijk is voor het milieu > 12 mijl van land, anders afgeven • Binnen special area alleen overboord als er geen haven ontvangst installaties beschikbaar zijn in beide havens. • Voor elke (be)lading moet duidelijk zijn of de lading schadelijk is voor mens en milieu volgens de 7 criteria genoemd in par 3.2 in de richtlijn. Gebaseerd op een tussentijdse maatregel geldig tot december 2014. (IMSBC of MEPC.1/Circ.791) • Onder droge lading restanten wordt niet verstaan het stof dat overblijft na het vegen of schoonmaken.
Inspectie Leefomgeving en Transport
Annex V en schoonmaakprodukten • De producent van het produkt moet zelf verklaren of het produkt onschadelijk is. • Ladingrestanten vermengt met water en schoonmaakmiddel mogen overboord alleen als zij niet schadelijk zijn voor het milieu • De tijdelijke permissie voor lozen van ladingrestanten in special area van de Golf, Middellandse zee en Caribische gebied volgens MEPC.1/Circ.675/Rev.1 is vervallen per 1-1-13 • Als in de vertrek en de aankomst haven geen afval ontvangstmogelijkheden zijn dan mag het >12 mijl overboord worden gezet als het geen gevaar kan voor het milieu. • Afgifte en lozing vermelding in het vuilnis boek
Inspectie Leefomgeving en Transport
Annex V en HH • • • • • •
Geen certificaat maar wel een logboek vereist Vuilnis management plan behoeft geen goedkeuring Vuilnis boek moet voldoen aan het IMO model. Posters moeten zijn opgehangen Afval melding in het kader van de EU richtlijn Op basis van hoeveelheid afval aan boord en de EU afgifte plicht (Geld niet voor ladingrestanten)
• HH op Ladingrestanten is verbeterd omdat: – Verplichte melding in vuilnis boek – Verplichte classificatie (MEPC.1/Circ.791)
Inspectie Leefomgeving en Transport
Annex VI Hoofdstuk 4 Energie efficiëntie • • • • •
Geld voor schepen > 400GT EEDI voor elk nieuw schip na 1-1-13 SEEMP op elk schip tijdens 1e tussentijdse of groot survey na 1-1-13 SEEMP geen goedkeuring vereist En IEE certificaat op elk schip tijdens 1e tussentijdse of groot survey na 1-1-13
• HH op aanwezigheid IEE en SEEMP
Inspectie Leefomgeving en Transport
MARPOL inspecties Gewoon doen !
Cees-Willem Koorneef Hoofd Inspectie Divisie Havenmeester Havenbedrijf Rotterdam N.V. © Copyright - Port of Rotterdam
77
Bio • bouwjaar 1966 • Douane Rotterdam 1985 • Port of Rotterdam 1990 • MARPOL superintendent • Hoofd Centrale Meldkamer Havenmeester 2006 • Hoofd Inspectie 2009
© Copyright - Port of Rotterdam
78
Eerst even dit • Havenmeester (DHMR) is onderdeel Havenbedrijf Rotterdam • Convenant • Verantwoording afleggen
© Copyright - Port of Rotterdam
79
Sinds 1987 • Start MARPOL taken • Scheepvaart inspectie en Havendienst
© Copyright - Port of Rotterdam
80
Anno nu • samenwerkingsovereenkomst Wet voorkoming verontreiniging door Schepen (WvvS) • Medetoezichthouder • Vernieuwing Toezicht
© Copyright - Port of Rotterdam
81
Zo werkt DHMR Inspectie • Safety and Environmental Index (SEI) • 9.0 • Risicogestuurd • HaMIS
© Copyright - Port of Rotterdam
82
Safety- & Environmental Index • De SEI is een gemiddelde waarde van het nalevingsgedrag aan boord van zeeschepen op basis van fysieke inspecties in een bepaalde periode.
• Voor de SEI geldt: • Op basis van fysieke inspecties • Afbreukwaarden bij tekortkoming • Afbreuk afhankelijk van ernst van de tekortkoming • Cijfer o.b.v. scheepstotaal
© Copyright - Port of Rotterdam
83
Meekijken in Rotterdam • HaMIS “live”
© Copyright - Port of Rotterdam
84
Dank voor uw aandacht!
[email protected]
© Copyright - Port of Rotterdam
85
EEDI VERIFICATIE Michiel Verhulst
INHOUD • • • •
Verificatie proces Def. verificatie tijdens proeftocht Model testen tijdens ontwerp Onzekerheden in EEDI bepaling
87
EEDI TO REDUCE CO2 EMISSIONS Proces
88
Proeftocht
Model testen
Onzekerheden
VERLAGING REQUIRED EEDI Proces
Proeftocht
Model testen
Onzekerheden
Required EEDI waarden General Cargo Ships, per phase phase1: 2015 phase2: 2020
phase3: 2025
89
VERIFICATION PROCESS & INDUSTRY WG Proces
Proeftocht
Model testen
Onzekerheden
Verifier zal meestal klasse zijn
Pre-verification ontwerp Final verification proeftocht
WANNEER IS CFD TOEGESTAAN? Proces
Proeftocht
Model testen
Onzekerheden
First version of the industry guidelines: • ‘The speed power curves for these two loading conditions are to be based on tank test measurements’ • ‘A tank test for an individual ship may be omitted based on technical justifications such as availability of the results of tank tests for ships of the same type’ Verification Guidelines: • ‘Ship of the same type means a ship of which hull form excluding additional hull features such as fins and of which principal particulars are identical to that of the base ship’
91
FINAL VERIFICATION Proces
Proeftocht
Model testen
Proeftocht om gegeven het vermogen (75% MCR) de referentie snelheid Vref te bepalen Dit geeft de def. attained EEDI Op EEDI diepgang (summer draught voor bulkers, gen. cargo)
EEDI conditie: diep water, geen wind en golven
92
Onzekerheden
PROCEDURE PROEFTOCHT Proces
Proeftocht
Model testen
Uitvoering • Meet snelheid over de grond en asvermogen • Double runs om effect stroming te elimineren • Een keer in kopgolven, terug-run achterinkomende • Corrigeer vermogen voor wind en golven • Conversie naar beladen conditie via modelproeven 93
Onzekerheden
ANALYSE METHODEN Proces
Proeftocht
Model testen
Onzekerheden
Analyse methoden oa: • ISO 15016 in 2002 uitgekomen. Keuze uit verschillende verschillende golf correctie methoden Grote verschillen! • STA (Sea trial Analysis JIP) 2006. Introductie van STAWAVE 1 en 2
Model test results, ISO methods and STAWAVE, head waves 94
STA OF ISO? Proces
Proeftocht
Model testen
• STA procedure opgenomen in nieuwe ITTC guideline voor speed/power trials • Beide methoden (ITTC en ISO 15016) mogen gebruikt worden voor EEDI verificatie, te veel vrijheid in keuze golfcorrecties • ISO is bezig om samen met ITTC beiden in lijn te brengen
95
Onzekerheden
PRE-VERIFICATIE Proces
Proeftocht
Model testen
Onzekerheden
Modelproeven voor pre-verificatie en omrekening ballast (proeftocht) naar beladen (EEDI) conditie ballast Vballast -> Pmeas/Ppred
Full load Pmeas/Ppred*Ppred->Vref
96
EXTRAPOLATIE MODEL PROEF Proces
Proeftocht
Model testen
Onzekerheden
Ct (-)
Correlation Allowance (Ca) is ervaringsgetal om te compenseren voor bekende en onbekende tekortkomingen, oa: • luchtweerstand schip (geen bovenbouw) • Ruwheid (model is te glad) 3 • … 2.5 Dus dichten van het gat 2 tussen modelproef en 1.5 ware-grootte 1
Ca Model test
0.5
ΔCa = Caballast - Cabeladen 97
0 Beladen
Ballast
BALLAST/LADEN CORRELATION ALLOWANCE Proces
Proeftocht
Model testen
Onzekerheden
Waargenomen variaties in ∆Ca als functie van displacement verhouding
~12% vermogen! ∆Ca
MARIN standaard
98
Δ/ Δfull
GUIDELINES VOOR CA VERSCHIL Proces
Proeftocht
Model testen
Onzekerheden
Industry guidelines: • ‘In particular, the verifier will compare the differences between experience based coefficients Ca between EEDI condition and sea trial condition’ • ‘If the difference is significantly higher than the values reported in the figure, a proper justification…’ Wat is significantly higher? Betere grens nodig, grote invloed Vref
99
ONZEKERHEID EEDI BEPALING Proces
Proeftocht
Model testen
Onzekerheden
Meetonzekerheid heeft te maken met nauwkeurigheid en precisie:
Onnauwkeurig, niet precies Onnauwkeurig, precies Nauwkeurig, niet precies Nauwkeurig, precies
We spreken over betrouwbaarheids interval, bv U95=2σ Onzekerheid in Vref en EEDI is +/- factor 3 kleiner dan in vermogen
ONZEKERHEID WARE GROOTTE Proces
Proeftocht
Model testen
Onzekerheden
Meetonzekerheid: • Standaard deviatie vermogen (vd Boom, 2012) =1% Reproduceerbaarheid: • Correctie voor niet ideale omgevingcondities • Zusterschepen van dezelfde werf: • Serie bulkcarriers (11): std P = 2.9% • Serie containers (8): std P = 4.0%
Komt overeen met ITTC Performance Commitee (4.5%) In EEDI is dit dus 2*4.5/3= +/-3% (inclusief zusterschepen)
BOVEN/ONDER REQUIRED EEDI Proces
Proeftocht
Model testen
Onzekerheden
Vier meetresultaten (attained EEDI’s) met betrouwbaarheden tov een limiet: specified upper limit
a
b
c
d
Geval a voldoet, d te hoge EEDI Voor geval b&c geen conclusie mogelijk Moet de attained EEDI bv 2% onder de required blijven? Of is dit een marge? Wanneer voldoet het schip? 102
CONCLUSIE • Model proeven altijd verplicht behalve bij ‘ship of the same type’ Wat wordt rol CFD? Beter specificatie wanneer wel en niet.
• ISO 15016 en STA methode beiden toegestaan voor proeftochtcorrectie. Te veel vrijheid. Naar een methode? • ‘Experience based coefficients’ in extrapolatiemethode zijn nodig, maar ITTC heeft geen concrete aanbeveling voor verschillen ballast beladen, grote invloed Vref
• Meten van Vref met eindige betrouwbaarheid, gevolgen voor required EEDI? Mag je bv 2% erboven zitten? (CJIB)
103
THANK YOU!